Installation to suit you
Service Guarantee
Price Match Promise
Reassurance Guaranteed

Don’t miss out!

Days
Hours
Minutes
Seconds

Fitting Your Alfresco Kit

Fitting your new Alfresco balustrades is designed to be very straightforward, making it an achievable for any capable DIY’er.

Wired Balustrade Kit

In a nutshell, this is how simple the fitting process is for Alfresco Wired Balustrade Kits. See the video for full instructions.

Layout the posts for each section next to the handrail, on the floor. Fix the posts to the handrail using the supplied bolts, through the pre-drilled and riv-nutted holes in the handrail. 

Carefully lift the balustrade up, one section at a time (with one person on each post to avoid any twisting) and place it in position. 

Use a suitable pen or pencil to mark the holes on the base fixing plate for each post, then carefully move the balustrade to one side and drill the holes with a suitable drill bit. 

Place the balustrade back in position and bolt the posts the floor, using a spirit level and any necessary shims to ensure the posts are plumb vertical. Once securely fastened, connect each wire and tension one at a time. 

Framed Glass Balustrade Kit

In a nutshell, this is how simple the fitting process is for Framed Glass Balustrade. See the video for full instructions.

Layout the posts for each section next to the handrail, on the floor. Fix the posts to the handrail using the supplied bolts, through the pre-drilled and riv-nutted holes in the handrail. Then, fit the wooden templates into the lower clamps.

Carefully lift the balustrade up, one section at a time (with one person on each post to avoid any twisting) and place it in position. 

Use a suitable pen or pencil to mark the holes on the base fixing plate for each post, then carefully move the balustrade to one side and drill the holes with a suitable drill bit. 

Use a suitable pen or pencil to mark the holes on the base fixing plate for each post, then carefully move the balustrade to one side and drill the holes with a suitable drill bit. 

Place the balustrade back in position and bolt the posts to the floor, using a spirit level and any necessary shims to ensure the posts are plumb vertical. Once securely fastened, one at a time, remove the wooden template from the clamps and replace it with the glass panel for that section. 

Frameless Glass Balustrade Kit

In a nutshell, this is how simple the fitting process is for our Alfresco Frameless Glass Balustrade Kit. See the video for full instructions.

Lay the base channel in position and mark the bolt-hole locations using a pen or pencil. Drill the holes with a suitable drill bit, then fix the base channel in position using M12 bolts. 

Place the isolators into the channel (3 per meter) and attach the rigid adjustment bead to the outer edge. Place the slider into the channel with the wings on the inside edge and the slider positioned to the right of the isolator.

Insert glass into the channel, put the clamps within the slider wings, and lower to the clip.

With the glass angled towards the installer, insert the wedge tools and maneuver the glass into the desired position by hand, using a spirit level.

Slide the clamps to the right, so that the slider is tight. Press the clip onto the clamps and push down into the channel.

Insert the clamp bars and bolts, and tighten them against the channel by unwinding the bolt. Then remove the wedge tool.

Repeat this process for each panel, one at a time. 

Apply the trim to the top of the base channel and the end caps to either end of the channel. 

Starting at the bottom of the stairs and working your way up, place the bespoke glass panels into position (using the spacer block provided to set the correct gap either side of the glass) in the clamps and tighten the clamps with an 8mm Allen Key.

Get Started with StairFurb

Request Alfresco Brochure

Whether you prioritise environmental sustainability and opt for our highly interactive digital brochure, or prefer the tactile experience of a printed brochure, we are delighted to accommodate your preference.

Get A Quote

Are you a DIY'er that takes pleasure in taking measurements, following instructions, and getting hands-on? Or perhaps you prefer the convenience of being guided through measurements by a knowledgeable sales assistant? Whichever option you prefer, we are equipped to meet your needs.
Save basket
Your Shopping basket and Stairfurb Configuration will be saved and you'll be given a link. You, or anyone with the link, can use it to retrieve your basket at any time.
Back Save basket
Your Shopping basket will be saved with Product pictures and information, and basket Totals. Then send it to yourself, or a friend, with a link to retrieve it at any time.
Your basket email sent successfully :)

FREE QUOTATION

X

Photo Estimate

Simply take a photo of each balustrade section and let us know which style you want. We’ll then estimate your dimensions and provide an idea of price.

GET PHOTO ESTIMATE

Video Call Measure

Get help measuring and a free no-obligation quote on a free 20-minute video call from the comfort of your own home. Speak with our expert team about your staircase upgrade.

BOOK CALL NOW

DIY Online Configurator

Measure your staircase using our online video tutorials and input them into our online configurator for a free, no-obligation quote. It takes less than 15 minutes.

START DIY QUOTE

FREE QUOTATION

X

Video Call Measure

Get help measuring and a free no-obligation quote on a free 20-minute video call from the comfort of your own home. Speak with our expert team about your staircase upgrade.

BOOK CALL NOW

DIY Online Configurator

Measure your staircase using our online video tutorials and input them into our online configurator for a free, no-obligation quote. It takes less than 15 minutes.

START DIY QUOTE